سيارة تايوتا فور رنر Radio 12v blue/yellow + radio harnessRadio Ground brown - radio harness Radio Ignition gray + radio harness Radio Illumination green + radio harness Factory Amp Turn-on N/A Power Antenna black + radio harness LF Speaker +/- pink - purple +,- radio harness or amplifier Notes: If equipped, the stereo amplifier is behind the passenger side quarter panel. RF Speaker +/- lt. green - blue +,- radio harness or amplifier LR Speaker +/- black - yellow +,- radio harness or amplifier RR Speaker +/- red - white +,- radio harness or amplifier Interface Module: Category: Immobilizer Bypass Required: Yes Type: Transponder Part #: 556UW Alternate Part1 #: DesignTech 20402 Alternate Part2 #: DesignTech 29402 Notes: Standard on all models. Smart Starter Kill Relays: Not Available 12volts white/blue (50A), red (30A) + ignition harness Starter green/black + ignition harness Second Starter N/A Ignition black/red + ignition harness Second Ignition blue/yellow + ignition harness Third Ignition N/A Accessory white/green + ignition harness Second Accessory N/A Keysense green/yellow - ign harn or BECU, top plug, pin 14 Notes: Using the status output to trigger this wire during remote start will disarm the factory alarm without unlocking the doors. The Body ECU is part of the fuse box under the driver side dash. The three plugs on the right side edge of the fuse box are for the Body ECU. Power Lock blue - driver kick, 18 pin plug Notes: Meter the wire while turning the key in the driver door key cylinder. Power Unlock green (double pulse) - driver kick, 18 pin plug Notes: Meter the wire while turning the key in the driver door key cylinder. Lock Motor blue/red to black/white 5wi driver kick, 13 pin plug Unlock Motor blue/black to black/red 5wi driver kick, 13 pin plug Parking Lights+ green + left of fuses, 16 pin plug Parking Lights- green - BECU, top plug, pin 8 Notes: The Body ECU is part of the fuse box under the driver side dash. The three plugs on the right side edge of the fuse box are for the Body ECU. Hazards white - hazard switch Turn Signal(L) blue/black + left of fuses, 16 pin plug Turn Signal(R) blue/yellow + left of fuses, 16 pin plug Reverse Light red/yellow + left of fuses, 16 pin plug Door Trigger purple/yellow - BECU, top plug, pin 12 Notes: Can also use individual door trigger wires in the middle plug at the BECU. The driver door trigger is red/black in pin 23, the passenger door is red/yellow in pin 24, the left rear door is pink/black in pin 11, and the right rear door is pink/blue in pin 12. Use all four wires and diode isolate each. The Body ECU is part of the fuse box under the driver side dash. The three plugs on the right side edge of the fuse box are for the Body ECU. Dome Supervision white - plug to right of fuses, pin 8 Trunk/Hatch Pin green/yellow - back door ECU in hatch Hood Pin pink/green - driver kick, blue 18 pin plug Trunk/Hatch Release N/A Power Sliding Door N/A Factory Alarm Arm arms with lock Factory Alarm Disarm disarms with unlock Disarm No Unlock use key sense wire Tachometer black/white ac ECM, 2nd plug from bottom, pin 1 Notes: The ECM (Engine Control Module) is behind the glovebox. On the 6 cylinder models, you can also find this wire at the data link connector under the driver side dash. Wait to start N/A Brake Wire green/yellow + left of fuses, 16 pin plug Parking Brake lt. green - BECU, middle plug, pin 2 Notes: The Body ECU is part of the fuse box under the driver side dash. The three plugs on the right side edge of the fuse box are for the Body ECU. Horn Trigger green/red - horn switch Memory Seat 1 pink - memory seat switch on dash Memory Seat 2 purple - memory seat switch on dash Memory Seat 3 N/A - Interface Module: Category: Immobilizer Bypass Required: Yes Type: Transponder Part #: 556UW Alternate Part1 #: DesignTech 20402 Alternate Part2 #: DesignTech 29402 Notes: Standard on all models. Smart Starter Kill Relays: Not Available warning This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. |