سيارة تايوتا سينا  2005

[PRINT THIS PAGE]

12volts      wht/red (30A), wht/blue (7.5A)      +       ignition harness
Starter      black/yellow       +       ignition harness
Second Starter      N/A            
Ignition      black       +       ignition harness
Second Ignition      black/yellow       +       ignition harness
Third Ignition      N/A            
Accessory      pink       +       ignition harness
Second Accessory      N/A            
Keysense      blue/black       -       ignition harness
Notes: Using the status output to trigger this wire during remote start will disarm the factory alarm without unlocking the doors.
Power Lock      lt. green       -       driver kick, 18 pin plug
Notes: Meter these wires while turning the key in the driver door key cylinder.
Power Unlock      blue (double pulse)       -       driver kick, 18 pin plug
Notes: Meter these wires while turning the key in the driver door key cylinder.

Can also use the passenger door key cylinder wire for unlock, which only requires a single pulse. It is blue/yellow (-) in the passenger kick in a 12 pin plug.
Lock Motor      blue/red       5wi      driver kick, 12 pin plug
Unlock Motor      white/red to red       5wi      driver kick, 18 pin plug
Parking Lights+      do not use, relay rests at gnd           
Parking Lights-      green/black       -       headlight switch
Hazards      black/orange       -       hazard switch
Turn Signal(L)      green/black       +       R side of fuse box, 30 pin plug
Turn Signal(R)      green/yellow       +       R side of fuse box, 30 pin plug
Reverse Light      red/black       +       driver kick, harness to rear
Door Trigger      blue       -       interior light switch on dash
Notes: Can also use individual door trigger wires. The driver door is red/yellow in the 16 pin plug, pin 14 at the BECU. The passenger door is red/yellow in the 28 pin plug, pin 23 at the BECU. The left sliding door is gray, pin 19, in a 25 pin plug on the right side of the fuse box. The right sliding door is red/white in the 16 pin plug, pin 16 at the BECU. The hatch door is green/white in the 28 pin plug, pin 25 at the BECU. Use all wires and diode isolate each.

The BECU (Body ECU) is attached to the back of the fuse box under the driver side dash.
Dome Supervision      red/green       -       interior light switch on dash
Trunk/Hatch Pin      common with door trigger wire            
Hood Pin      red/white       -       BECU, 10 pin plug, pin 10
Notes: The BECU (Body ECU) is attached to the back of the fuse box under the driver side dash.
Trunk/Hatch Release      yellow/red (power back door)       -       bottom L of fuse box, 22 pin plug
Notes: On vehicles without the power back door, the hatch release is green/black (-) at the BECU, 28 pin plug, pin 3. Meter this wire while open the hatch from the handle on the rear hatch.

The hatch release motor wire is blue/black (+) at the BECU, 26 pin plug, pin 1.

The BECU (Body ECU) is attached to the back of the fuse box under the driver side dash.
Power Sliding Door      yellow/green (L), purple (R)       -       bottom L of fuse box, 22 pin plug
Factory Alarm Arm      arms with lock            
Factory Alarm Disarm      disarms with unlock            
Disarm No Unlock      use key sense wire            
Tachometer      black/orange       ac       ECM, top plug, pin 5
Notes: The ECM (Engine Control Module) is behind the glove box.
Wait to start      N/A            
Brake Wire      green/white       +       brake pedal switch
Parking Brake      red/white       -       R side of fuse box, 36 pin plug
Horn Trigger      green/black       -       horn switch
Memory Seat 1      N/A            
Memory Seat 2      N/A            
Memory Seat 3      N/A            
Interface Module:      Category:
Immobilizer Bypass      Required:
Yes      Type:
Transponder
Part #: 556UW
Alternate Part1 #: DesignTech 20402
Alternate Part2 #: DesignTech 29402
Notes: Standard on LE, XLE, and XLE Limited models.
Smart Starter Kill Relays:      Relay Type:
EFI Relay      Location:
Engine compartment fusebox, Driver side
Part #: 6413A


warning      
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed Electronics assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.