تعبئة الحبر للطابعات اللتي تحوي شريحة الكترونية

[winkod]

اساتذتي الكرام هل منكم من تطرق لشرح موضوع الطابعات التي تحوي شريحة الكترونية مع الكارتريج بعض الطابعات الليزرية و هل هذا يتطلب شراء كيت جديد مع الشريحة الجديدة
او يمكن التعبئة يرجى الشرح المفصل لو سمحتم

[sawa2007]

سؤالك نفس سؤالي أخي الكريم أرجو أن أجد جواب في هذا الموقع الرائع

[خالد السياغي77]

أرجو أخواني في المنتدى شرح صيانه طابعه شارب رقم Ar-407 وأرساله الي بريد alsoba3i************* ولكم جزيل الشكر والتقدير

[winkod]

هل من المعقول انه لا يوجد احد يعرف الاجابة عن سؤالي

لو يتكرم احد من المهندسين الاكارم بس يجاوبنا

لاني من جديد سمعت ان هالشريحة ممكن يعاد برمجتها من جديد

كيف ؟ و شو الطريقة ؟ و هل هذا الكلام صحيح او غير ممكن لان الشريحة يوجد عليها ic

و أي اي سي على الاغلب ممكن ان يعاد برمجتها بس وين المبرمجة اللي تشتغل معاها ؟

و شكرا

[f-jaser]

السلام عليكم
ان نسبة نجاح تعبئه كاتريج تحتوي على شريحه 5% وهناك خطوات قد تنجح في التعبءه لكن ننصح بتغير الماتريج افضل

[محمدعبدالعباس]

عمل دائرة الكترونية تحتوي على اربع زنر دايو قيمة 3و3 فولت مع سبع مقاومة قيمتها واحد كليو اوم مع البرامج في الحاسبة على نظام دولفن وعندي الرسم مع البرامج لتصفير العداد وشكــــــــــــــــــــــــــــرا لكم محمد ديوانية

[winkod]

مشكور كتير اخوي محمد عبد العباس
و الباقي عليك لو سمحت حتى يكمل الوضوع يعني البرنامج و المخطط

و انا منتظرك على احر من الجمر

[dim106]

مشكور الزميل عبدالعباس..
بانتظارك ياغالي...

[nabil bba]

الدارة موجودة في المساعدة لبرنامج
SSC Service Utility 4.2
http://www.ssclg.com/download/sscserve.exe
Resetter

Contents of this main window tab are dedicated to work with special add-on device connected to parallel port of your computer.
This device allows reset and total rewrite of any chips.

As known, for most of fairly new printer models it is impossible to reset chip ink counters by software only methods. But starting from v4.00 this utility allows reset and total rewrite of any chip by assembling very simple device that will be connected to your computer port. Full rewrite allows, for example, to make light cyan R300 chip from black C42 chip.

Main options

After you have selected printer model on other tab, in Available data for selected model dropdown list you could see all cartridges compatible with you printer model. Select cartridge you want to work with.

In case of UNSUP abbreviation after cartridge name and color, you couldn't write chip image, because this chip is not currently presented in program chip database. Yet if you have this cartridge chip, you can read his image and send us normal test report to allow us to include chip data to one of the next program versions. Even before new version will be released you can work with chip data as if chip is already in database.

Dropdown list Port allows you to select port address you have connected your device to. You can also select automatic port determination. In case of automatic determination problems we suggest you to set printer address directly. You can find port address using Windows device manager.

Chip shows you chip type you will be working with. Old type chips, in most cases, can be resetted by software, so device described below in this section don't have support for them. But software part is tested to work with old chips. We'll provide additional information now to modify device on our site.

New type chips are connected in parallel in printer head, therefore each chip have its own Address. In most cases automatically set chip address don't need to be modified. In case of chip not working correctly with selected address, you can try to change it or set Auto to automatically find proper one.

We don't recommend to use Auto setting in Address list for writing of checking operations.

If tick is on for Check chip presence then software checks chip presence in contactor before performing any operation with chip. Function works only if you connected ON wire in your device.

Speed slider allows you to set speed for all main operations with chip. Too hight or too low speed can lead to errors.

Main operations with chip

Write - Fully rewrites all chip contents. Many non-original cartridges do not allow rewriting all their contents except few bytes, in this case only few first bytes will be changes.

Ink counters for all chips contained in program database are zero.

Check - Utility reads all chip contents and compares them with data contained in database for selected chip. Utility reports you number of differences found. In case of successfull write operation check must show you 0 differences.

Read - Reads all chip contents and adds them to database. his operation is possible for unsupported cartridges only (with UNSUP mark). After successful readout program asks you about resetting ink counters.

Test - Allows to feed test signals to add-on device. all chip contents and adds them to database. his operation is possible for unsupported cartridges only (with UNSUP mark). In more detail assembling and testing of add-on device are described below.

Add-on device (resetter)

For assembling stage you need:
- solderer and solder alloy
- multimeter instrument
- 25-conductor flat cable, 1 meter, (it is possible to use part of more wide flat cable)
- DI-25m connector (25 contacts, male, with flat cable mount)
- small wiring board
- 7 resistors (rated values are depicted on electric circuit)
- 4 Zener diodes C1-C4 (stabilitrons, use any 0.5w, 3.3v, like BZX55C 3V3)
- 1 transistor T1 ( BC546C, BC547C or similar ones)

- RJ45 socket

Below you'll find electric circuit of add-on device.
Wiring board is marked by semitransparent light-green color.
On picture you'll find pinout for all used components.



Insert flat cable (use approx. 0.5m) in connector mount and fix it.
Solder all circuit on wiring board.
Now solder flat cable from connector and small flat cable (about 0.3m) what'll lead to chip contactor.

Study how chip contactor looks like in your printer head.

Using suitable RJ45 socket it is possible to make some resemblance of original contactor by slightly breaking socket,
then by cutting and bending necessary thin springy contacts similarly to original contactor. Then you must solder small
flat cable to contactor. Use contacts pinout shown on chip picture.

For users of C42 or similar printers, with small flat cable leading to chips. You can buy similar flexible flat cable and use your
print head as contactor by removing original flat cable and inserting yours. Pinout for C42 flat cable : 1-RST,2-3V,3-DTA,4-GND,5-CLK.

It is possible to make contactor using socket contacts and piece of transparent plastic with small holes.
You you invented some other easy and suitable way to make good contactor, write us about it, we'll add your instructions here.

How to check assembled device

Do not try to test device with chip in contactor.

Connect your device to port. Select Auto in Port list.

Press Test button. Answer positively to program question about testing procedure.

Program will show you first message and ask to press OK.

Get your multimeter and measure voltage on small flat cable wires leading to contactor.
Measure voltage between RST and GND, 3V and GND, DTA and GND, CLC and GND.
Measured voltage must be around 0 v.

Press OK button.

Measure voltage between RST and GND, 3V and GND, DTA and GND, CLC and GND.
Measured voltage must be higher then 2.9 v. If measured is lower then required you can get errors working with chip.
Minimum voltage is common for DTA. If it is very low try to reduce correspoding resistor value.

Press OK button.

Run test another time. In this time look at the value placed after Readed word.

This value must be 1 in first message and 0 in next.

All further testing must be performing with chip in contactor. Use check chip operation.
Read error indicates wrong device functioning.

[nabil bba]

تعبئة الحبر للطابعات اللتي تحوي شريحة الكترونية (http://www.qariya.com/vb/showthread.php?t=25202)

[mwjahead]

تعبئة الحبر للطابعات اللتي تحوي شريحة الكترونية (http://www.qariya.com/vb/showthread.php?t=25202)



بارك الله فيك

وجعلها في ميزان حسناتك

ولكن كمكنا نتمنى

لو أنها باللغة العربية

على كل حال مجهود رائع

ننتظر المزيد من إبداعاتك المذهلة

تحياتي

[nabil bba]

http://www.qariya.com/vb/D:%5CSans%20titre.jpg